防水卷材耐熱性懸掛裝置是**檢測儀器，含3個夾子，6個銅釘，3個劃線裝置。使用前務必仔細閱讀說明書。
The waterproof coil heat-resistant suspension device is a testing instrument, including 3 clips, 6 copper nails, and 3 scribing devices. Be sure to read the instructions carefully before use.
防水卷材耐熱性懸掛裝置使用方法：
先將試樣按規定尺寸裁剪好，然后把試樣需要刮除的部分事先劃出線。將刮刀放在電熱爐(需自備)上加溫，等刮刀足夠熱后，在正反兩面按標準用20mm刮刀刮除20×15mm的兩個區域(直至胎體)，用40mm的刮刀刮除100×15mm的區域(直至胎體)。
刮涂干凈后，將劃線器裝在20×15mm的區域，在試件的裸露區上打好眼，用插銷將兩個劃線器固定好后，用記號筆在正反兩面分別沿試件寬度方向劃線。
How to use the heat-resistant suspension of waterproof membrane:
First cut the sample according to the specified size, and then draw a line beforehａnd to scrape the sample. Put the scraper on the electric heating furnace (need to bring it) to warm up. After the scraper is hot enough, scrape the two areas of 20 × 15mm (up to the carcass) with a 20mm scraper according to the standard on both sides, and scrape with a 40mm scraper Exclude the 100 × 15mm area (up to the carcass).
After scraping, install the scriber in an area of 20 × 15mm, make a good eye on the exposed area of the test piece, fix the two scribers with a pin, and then use a marker to test the front and back sides respectively. Piece width direction.
防水卷材耐熱性懸掛裝置劃線完畢后，將劃線器卸下，用夾子夾在100×15mm的區域，涂蓋層不要夾到，必要時用如硅紙(需自備)的不粘層包住兩面，便于試驗結束時除去夾子。
After the waterproof coil heat-resistant suspension device has been scribed, remove the scribing device and clamp it in an area of 100 × 15mm with a clip. Do not pinch the coating layer. The adhesive layer covers both sides to facilitate removal of the clips at the end of the test.
防水卷材耐熱性懸掛裝置符合 GB/T 328 中規定防水卷材在溫度升高時的抗流動性測定，試驗卷材的上表面和下表面在規定溫度或連續在不同濕度測定的耐熱性**限。
試驗用來檢驗產品耐熱性要求，或測定規定產品的耐熱性**限，如測定老化后性能的變化結果.
The waterproof coil heat-resistant suspension device complies with the determination of the resistance to flow of the waterproof coil when the temperature rises as specified in GB / T 328. The upper and lower surfaces of the test coil are measured at the specified temperature or continuously at different humidity. Sexual restrictions.
The test is used to check the heat resistance requirements of the product, or to determine the maximum heat resistance limit of the specified product, such as determining the results of changes in properties after aging.
防水卷材耐熱性懸掛裝置(由夾子，劃線器，插銷等組成)中規定防水卷材在溫度升高時的抗流動性測定，試驗卷材的上表面和下表面在規定溫度或連續在不同濕度測定的耐熱性**限。試驗用來檢驗產品耐熱性要求，或測定規定產品的耐熱性**限，如測定老化后性能的變化結果
Waterproof membrane heat-resistant suspension device (composed of clips, scribes, pins, etc.) specifies the resistance to flow of the waterproof membrane when the temperature rises. The upper and lower surfaces of the test membrane are at the specified temperature or continuous. Limit of heat resistance measured at different humidity. The test is used to check the heat resistance requirements of the product, or to determine the maximum heat resistance limit of the specified product, such as the result of measuring the change in properties after aging.
